Fujitsu Reverse Cycle Air Conditioner Manual

The Fujitsu Reverse Cycle Air Conditioner is an advanced climate control system featuring cooling and heating modes, energy-efficient inverter technology, multiple fan speeds, timer functions, sleep mode, air purification filters, remote control operation, and smart temperature management. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Indoor unit with LCD display, outdoor compressor unit, remote control, air filters, temperature sensors, and multiple operation modes.

Installation Requirements

Professional installation recommended. Ensure proper location and electrical requirements.

1. Location selection: Choose well-ventilated area away from direct sunlight and heat sources.
2. Electrical connection: Requires dedicated circuit with proper voltage (220-240V).
3. Drainage setup: Install drain hose with proper slope for condensation removal.
4. Outdoor unit placement: Ensure adequate clearance for airflow and service access.

WARNING! Installation must be performed by qualified technician. Incorrect installation may cause electric shock or fire hazard.

First-Time Setup

After installation, perform initial setup for optimal performance.

1. Power on unit: Use remote control or indoor unit power button.
2. Set operating mode: Select Cool, Heat, Fan, Dry, or Auto mode.
3. Adjust temperature: Set desired temperature using temperature buttons.
4. Configure timer: Program on/off times for daily operation.
5. Test all functions: Verify cooling, heating, and fan operations.

CAUTION! Allow unit to stabilize for 10 minutes after initial startup.

Technical Specifications

• Cooling Capacity: 2.5kW - 7.1kW (model dependent)
• Heating Capacity: 2.8kW - 8.0kW (model dependent)
• Power Supply: 220-240V, 50Hz
• Refrigerant: R32 eco-friendly refrigerant
• Noise Level: 19-45 dB (indoor), 46-58 dB (outdoor)
• Energy Rating: 3-5 stars (model dependent)
• Air Flow: Up to 12.5 m³/min
• Operating Range: Cooling: -10°C to 46°C, Heating: -15°C to 24°C
• Dimensions: Varies by model series

Controls and Settings

Access functions via remote control or indoor unit buttons. Main controls: POWER, MODE, TEMP, FAN, TIMER, SWING.

Remote Functions: POWER, MODE selection, Temperature adjustment, Fan speed, Timer set/cancel, Swing control, Sleep mode, Turbo function, Filter reset.

Mode Settings: COOL (blue snowflake), HEAT (red sun), DRY (water drop), FAN (fan icon), AUTO (automatic selection). Temperature Range: 16°C - 30°C. Fan Speeds: Auto, Low, Medium, High, Quiet. Timer: 24-hour programming with 10-minute increments.

Operating Modes

Multiple operation modes for different climate needs.

1. Cooling Mode: For hot weather - set desired temperature
2. Heating Mode: For cold weather - automatic defrost cycle
3. Dry Mode: Reduces humidity without overcooling
4. Fan Mode: Circulates air without cooling/heating
5. Auto Mode: Automatically selects cooling or heating
6. Sleep Mode: Gradually adjusts temperature for comfort
7. Eco Mode: Optimizes energy consumption
8. Turbo Mode: Maximum cooling/heating power

Tip: Use Auto mode for energy-efficient operation.

Maintenance Procedures

Regular maintenance ensures optimal performance and longevity.

1. Filter cleaning: Clean air filters every 2 weeks during heavy use
2. Outdoor unit: Keep area clear of debris and vegetation
3. Drainage check: Ensure drain hose is not blocked
4. Professional service: Annual maintenance by qualified technician
5. Self-clean function: Run periodically to dry indoor unit
6. Winter preparation: Protect outdoor unit from ice buildup

WARNING! Always disconnect power before performing any maintenance.

Energy Saving Tips

Maximize efficiency and reduce operating costs.

• Set temperature to 24-26°C in cooling mode
• Use timer to avoid unnecessary operation
• Keep doors and windows closed during operation
• Clean filters regularly for optimal airflow
• Use Eco mode for extended operation
• Ensure proper insulation in room
• Close curtains during hottest part of day

Care & Cleaning

Proper cleaning maintains performance and air quality.

1. Unplug unit before cleaning
2. Clean air filters with vacuum or warm water
3. Wipe indoor unit with soft, dry cloth
4. Clean outdoor unit fins with soft brush
5. Check and clear drain pipe regularly
6. Avoid using chemicals or abrasive cleaners

CAUTION! Do not use water to clean electrical components. Never operate without filters.

Regulatory Information

Complies with Australian Standards AS/NZS 60335.2.40. Energy Rating Label as per Australian regulations. Refrigerant handling requires licensed technician. Manufactured under ISO 9001 quality standards. Contains R32 refrigerant - do not vent to atmosphere. For technical support, contact Fujitsu Australia at 1300 555 808 or visit www.fujitsugeneral.com.au.

Troubleshooting Guide

Reset Procedure: Turn off at power point for 10 minutes, then restart.

Service Support: 1300 555 808; www.fujitsugeneral.com.au