Fujitsu Motherboard Manual

The Fujitsu Motherboard is a high-performance computing platform designed for reliability and efficiency. This motherboard supports various Intel and AMD processors, multiple RAM configurations, PCIe expansion slots, SATA and NVMe storage interfaces, integrated graphics, and comprehensive connectivity options. Below are key sections for installation, specifications, BIOS setup, troubleshooting, and maintenance.

Features at a Glance

Key components: CPU socket, RAM slots, PCIe expansion slots, SATA connectors, M.2 slots, rear I/O panel, front panel headers.

Installation Guide

Unpack and inspect all components. Prepare anti-static workspace.

1. Install CPU: Lift socket lever, align CPU pins with socket, lower lever to secure.
2. Install RAM: Open DIMM clips, align notch, press firmly until clips lock.
3. Mount motherboard: Align with standoffs in case, secure with screws.
4. Connect power: Attach 24-pin ATX and 8-pin CPU power connectors.
5. Connect front panel: Power switch, reset switch, HDD LED, power LED.

WARNING! Always use anti-static wrist strap. Handle components by edges only.

BIOS Setup

Access BIOS by pressing DEL during boot. Navigate with arrow keys.

1. Main: System time, date, and basic system information.
2. Advanced: CPU configuration, chipset settings, storage configuration.
3. Boot: Boot order, boot mode (UEFI/Legacy), fast boot settings.
4. Security: BIOS passwords, secure boot, TPM configuration.
5. Save & Exit: Save changes and exit or discard changes.

CAUTION! Incorrect BIOS settings may cause system instability.

Specifications

• Form Factor: ATX (305mm x 244mm)
• CPU Support: Intel Core i3/i5/i7/i9 or AMD Ryzen 3/5/7/9
• Memory: 4x DDR5 DIMM, up to 128GB, 4800MHz+
• Expansion: PCIe 5.0 x16, PCIe 4.0 x1, PCIe 3.0 x4
• Storage: 6x SATA 6Gb/s, 2x M.2 PCIe 4.0 x4
• Audio: Realtek ALC1220 7.1 Channel
• LAN: 2.5 Gigabit Ethernet
• Wireless: Wi-Fi 6E + Bluetooth 5.2
• Power Requirements: ATX 12V v2.4
• Operating Temp: 0°C to 40°C

Connectors and Ports

Rear I/O: USB ports, audio jacks, network ports, video outputs.

Internal Headers: Front panel audio, USB 2.0/3.0, CPU fan, system fan, RGB headers, TPM header.

Power: 24-pin main power, 8-pin CPU power, SATA power. Storage: SATA data connectors, M.2 slots. Expansion: PCIe slots with retention clips. Diagnostic: POST code display, debug LEDs.

Memory Configuration

Supports dual-channel memory architecture. Install in correct slots for optimal performance.

1. For two modules: Install in A2 and B2 slots (usually second and fourth)
2. For four modules: Fill all DIMM slots
3. Enable XMP/EXPO in BIOS for rated speeds
4. Verify stability with memory stress tests

Tip: Consult QVL for tested memory compatibility.

Expansion Slots

PCIe 5.0 x16 for graphics cards, PCIe 4.0 x1 for add-on cards, PCIe 3.0 x4 for storage.

1. Primary GPU: Install in PCIe 5.0 x16 slot (top slot)
2. Additional cards: Use remaining PCIe slots
3. Remove slot covers from case before installation
4. Secure cards with retention screws

WARNING! Ensure proper power supply for high-power graphics cards.

Storage Configuration

Supports SATA and NVMe storage devices. Configure in BIOS.

1. SATA drives: Connect data cable to motherboard, power to PSU
2. M.2 NVMe: Insert at 30-degree angle, secure with screw
3. RAID configuration: Enable in BIOS, configure array
4. Boot priority: Set in BIOS boot menu

CAUTION! Handle M.2 drives carefully to avoid damage.

Maintenance & Care

Power off and unplug before maintenance. Use compressed air for dust removal.

CAUTION! Avoid liquid cleaners. Check for capacitor bulging or damage.

Regulatory Information

FCC Part 15 Class B compliant. CE marked. RoHS compliant. Copyright © 2024 Fujitsu Limited. All trademarks are property of their respective owners. For technical support, visit www.fujitsu.com/support or contact 1-800-富士通.

Troubleshooting

Reset: Clear CMOS jumper or remove battery for 30 seconds.

Service: 1-800-富士通; www.fujitsu.com/support