Fujitsu 6010n Manual

The Fujitsu 6010n is a high-performance network-ready laser printer designed for office environments, featuring fast printing speeds up to 30ppm, 1200x1200 dpi resolution, built-in Ethernet connectivity, USB 2.0 interface, automatic duplex printing, 32MB standard memory (expandable to 160MB), 250-sheet input capacity, and support for multiple operating systems including Windows, Mac OS, and Linux. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Laser printing engine, network interface card, control panel, paper trays, toner cartridge system.

Feature	Description
Print Speed	Up to 30 pages per minute
Resolution	1200x1200 dpi maximum
Memory	32MB standard (expandable to 160MB)
Paper Capacity	250-sheet input tray
Connectivity	Ethernet 10/100Base-TX, USB 2.0
Duplex Printing	Automatic two-sided printing
POWER Button	Turns printer on/off
Control Panel	LCD display and navigation buttons
Toner Save Mode	Reduces toner consumption
Network Ready	Built-in Ethernet interface

Installation

Unpack and inspect contents. Place on stable, level surface.

1. Remove all packaging materials and tape from printer.
2. Install toner cartridge: Open front cover, remove packaging, insert cartridge until it clicks.
3. Load paper: Adjust paper guides in input tray, load letter-size paper.
4. Connect power cable: Plug into AC power outlet.
5. Connect to computer: Use USB cable or Ethernet network cable.

WARNING! Printer contains high-voltage components; do not open covers except as instructed. Ensure proper ventilation.

First-Time Setup

Power on printer; follow initial setup procedure.

1. Install printer software: Insert CD or download drivers from Fujitsu website.
2. Network configuration: Use control panel to set IP address or enable DHCP.
3. Print test page: Verify printer operation and quality.
4. Configure settings: Set paper size, print quality, default settings via control panel.

CAUTION! Allow printer to complete initial warm-up cycle before first use.

Specifications

• Print Technology: Laser electrophotography
• Print Speed: Up to 30 ppm (letter/A4)
• Resolution: 1200x1200 dpi
• First Print Out: Less than 10 seconds
• Memory: 32MB standard, expandable to 160MB
• Paper Handling: 250-sheet input capacity
• Media Types: Plain, bond, recycled, labels, envelopes, transparencies
• Connectivity: USB 2.0, Ethernet 10/100Base-TX
• Power Consumption: 350W operating, 10W standby
• Dimensions: 15.4" x 15.7" x 13.8" (WxDxH)
• Weight: 31.7 lbs

Controls and Settings

Access functions via control panel LCD and navigation buttons.

Control Panel: POWER, GO (resume), CANCEL (stop), MENU, UP/DOWN arrows, ENTER.

Print Settings: Quality (600dpi, 1200dpi), Economy Mode, Paper Size, Orientation. Network: TCP/IP configuration, Protocol settings, Print server setup. Maintenance: Print configuration page, Clean mode, Reset functions.

Connecting Devices

USB: Direct computer connection. Network: Ethernet for multiple users.

1. Turn off printer before connecting cables.
2. USB connection: Connect USB cable to computer and printer.
3. Network connection: Connect Ethernet cable to router/switch and printer.
4. Install drivers on all computers that will use the printer.

Tip: For network installation, configure IP address through control panel menu.

Printing Operations

Supports various document types and media.

1. Load paper: Ensure paper guides are properly adjusted.
2. Send print job: From application, select Print and choose Fujitsu 6010n.
3. Monitor status: Check control panel LCD for job status and errors.
4. Special media: Adjust paper guides for envelopes or labels.
5. Duplex printing: Enable in printer properties for automatic two-sided printing.
6. Toner save: Activate in printer settings to reduce toner consumption.

WARNING! Do not touch the fuser unit; it becomes hot during operation.

Network Configuration

Configure network settings for shared office use.

1. Access network menu: Press MENU, navigate to Network Settings.
2. TCP/IP configuration: Set IP address manually or enable DHCP.
3. Protocol settings: Configure FTP, HTTP, SNMP as needed.
4. Print server: Access via web browser using printer's IP address.

Note: Default network settings may vary; consult network administrator.

Care & Maintenance

Unplug before cleaning. Use soft, dry cloth for exterior; approved cleaning materials for interior.

1. Regular cleaning: Wipe exterior with dry cloth.
2. Paper path: Clear any paper dust or debris.
3. Toner cartridge: Replace when print quality deteriorates or low toner warning appears.
4. Ventilation: Ensure vents are clear of obstructions.

CAUTION! Use only Fujitsu-approved toner cartridges and supplies.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. CE marked for European compliance. Energy Star qualified for energy efficiency. Copyright © Fujitsu Limited; all rights reserved. For support, visit www.fujitsu.com or contact 1-800-831-8093.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Printer not responding	Power/connections	Check power cable; ensure USB/network cable connected properly.
Poor print quality	Toner/paper	Replace toner cartridge; use recommended paper; run cleaning cycle.
Paper jams	Paper path obstruction	Open covers and carefully remove jammed paper; check for debris.
Network connection failed	IP configuration	Verify network settings; check cable connection; restart printer.
Toner cartridge error	Installation/defect	Reinstall toner cartridge; replace if defective or empty.

Reset: Menu > System > Reset to factory defaults if needed.

Service: 1-800-831-8093; www.fujitsu.com/support