fuji xt2 manual download

The Fujifilm X-T2 is a high-performance mirrorless digital camera featuring a 24.3MP X-Trans CMOS III sensor, X-Processor Pro image processing engine, 4K video recording, advanced autofocus system with 325 points, weather-resistant magnesium alloy body, dual SD card slots, tilting LCD screen, and extensive manual controls. Below are key sections for features, setup, operation, and technical specifications.

1. Key Features 2. Camera Setup 3. Basic Operation 4. Technical Specifications 5. Controls and Dials 6. Shooting Modes 7. Video Recording 8. Wireless Functions 9. Maintenance 10. Warranty Information 11. Troubleshooting

Key Features

Main components: X-T2 camera body, battery pack, charger, shoulder strap, body cap, hot shoe cover.

Feature	Description
24.3MP X-Trans CMOS III	APS-C sensor with no optical low-pass filter
X-Processor Pro	High-speed image processing engine
4K Video Recording	UHD 3840x2160 at 30p/25p/24p
Autofocus System	325-point hybrid AF with phase detection
Weather Resistant	91 points sealing against dust and moisture
Dual SD Card Slots	Supports UHS-II standards
Electronic Viewfinder	2.36M-dot OLED with 0.77x magnification
Tilting LCD Screen	3-inch 1.04M-dot three-direction tilting
Mechanical Shutter	1/8000 sec to 30 sec, bulb to 60 min
Continuous Shooting	Up to 8 fps (14 fps with battery grip)

Camera Setup

Unpack and verify all components. Charge battery before first use.

Insert battery: Open battery compartment, insert NP-W126S battery.
Insert memory card: Open card slot cover, insert SD card into slot 1 or 2.
Attach lens: Remove body and lens caps, align red dots, rotate clockwise.
Charge battery: Connect charger to AC power, charge until indicator turns off.

WARNING! Do not touch camera internals; keep away from water and extreme temperatures.

Basic Operation

Power on camera; set date/time and basic preferences.

Power on: Rotate power switch to ON position.
Set date/time: Follow initial setup prompts on LCD screen.
Select shooting mode: Use mode dial (P, A, S, M, AUTO).
Adjust exposure: Use front/rear command dials for aperture/shutter speed.
Focus: Half-press shutter button for AF, full press to capture.

CAUTION! Handle camera with care; use neck strap to prevent drops.

Technical Specifications

Sensor: 23.6mm x 15.6mm (APS-C) X-Trans CMOS III
Effective Pixels: 24.3 megapixels
Image Processor: X-Processor Pro
ISO Sensitivity: 200-12800 (extended 100-51200)
Shutter Speed: 1/8000 to 30 sec, Bulb (60 min)
Continuous Shooting: 8 fps (mechanical), 14 fps (electronic, with VPB-XT2)
Video: 4K/30p, Full HD/60p
Viewfinder: 2.36M-dot OLED, 100% coverage
LCD: 3.0-inch 1.04M-dot tilting
Battery: NP-W126S Li-ion battery
Dimensions: 132.5mm x 91.8mm x 49.2mm
Weight: 507g (including battery and memory card)

Controls and Dials

Top plate controls: Shutter speed dial, ISO dial, exposure compensation dial, metering selector, drive dial.

Rear controls: AF-L, AE-L, Q button, focus lever, playback, menu/OK, display/back.

Shooting settings: Exposure compensation (±5EV), ISO (200-12800), film simulation modes (Provia, Velvia, Astia, etc.), white balance (auto, custom, presets), focus modes (S, C, M). Custom functions: Assign buttons via SET-UP menu.

Shooting Modes

Program AE (P), Aperture Priority (A), Shutter Priority (S), Manual (M), AUTO, Advanced Filters.

Select mode via top dial.
P mode: Camera sets aperture and shutter automatically.
A mode: Set aperture, camera selects shutter speed.
S mode: Set shutter speed, camera selects aperture.
M mode: Manual control of both aperture and shutter.
AUTO: Full automatic operation for point-and-shoot.

Tip: Use exposure compensation dial for quick brightness adjustments.

Video Recording

Supports 4K UHD and Full HD video recording.

Set mode dial to movie position.
Press movie button to start recording.
Press again to stop recording.
Adjust settings: Frame rate, quality, microphone level.
Use Fn button for quick access to video settings.

WARNING! Continuous recording may cause overheating; allow cool-down periods.

Wireless Functions

Wi-Fi connectivity for remote control and image transfer via Fujifilm Camera Remote app.

Install Fujifilm Camera Remote app on smartphone.
Enable camera Wi-Fi from connection settings.
Connect smartphone to camera's Wi-Fi network.
Transfer images or use remote shooting function.

Maintenance

Use blower to remove dust from lens and body. Clean LCD with soft, dry cloth.

CAUTION! Do not use alcohol or solvents; store in dry place with silica gel.

Warranty Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
Camera won't turn on	Battery depleted	Charge battery; check battery orientation.
Memory card error	Card not formatted	Format card in camera; try different card.
Autofocus not working	AF mode setting	Set focus mode to S or C; clean lens contacts.
Images blurry	Shutter speed too slow	Use faster shutter speed; enable image stabilization.
Wi-Fi connection fails	Distance/obstacles	Move closer to camera; restart both devices.

Reset: Menu > SET-UP > USER SETTING > RESET

Service: Contact authorized Fujifilm service center; www.fujifilm.com/support