Fuji Prima T2 Service Manual

The Fuji Prima T2 is a professional-grade digital camera featuring advanced imaging technology, manual controls, and robust construction for professional photography applications. This service manual provides comprehensive technical information for maintenance, repair, and troubleshooting procedures. Below are key sections covering specifications, disassembly, maintenance, calibration, and service procedures.

1. Technical Specifications 2. Camera Overview 3. Disassembly Procedures 4. Maintenance Schedule 5. Calibration Procedures 6. Electrical System 7. Optical System 8. Mechanical Components 9. Firmware Updates 10. Service Tools 11. Troubleshooting Guide

Technical Specifications

Key technical parameters and performance characteristics of the Fuji Prima T2 camera system.

SpecificationDescription
Sensor Type24.3MP APS-C CMOS sensor
Image ProcessorFUJIFILM X-Processor Pro
Lens MountFUJIFILM X mount
ISO Range200-12800 (expandable to 100-51200)
Shutter Speed30-1/4000 sec (mechanical), 30-1/32000 sec (electronic)
Continuous ShootingUp to 8 fps
Video Recording4K UHD at 30p
Viewfinder0.5-inch OLED color viewfinder (3.69M dots)
LCD Screen3.0-inch tilting LCD (1.04M dots)
BatteryNP-W126S Li-ion battery

Camera Overview

Component identification and functional description of major camera assemblies.

  1. Front Assembly: Lens mount, sensor unit, grip assembly, control dials
  2. Rear Assembly: LCD screen, viewfinder, control buttons, navigation dial
  3. Top Assembly: Mode dial, shutter button, exposure compensation dial
  4. Bottom Assembly: Battery compartment, tripod socket, memory card slot
  5. Side Panels: Connection ports (USB, HDMI, microphone, remote release)

WARNING! Always discharge static electricity before handling internal components. Use proper ESD protection.

Disassembly Procedures

Step-by-step instructions for camera disassembly and component access.

  1. Battery and memory card removal: Ensure camera is powered off completely
  2. External cover removal: Remove rubber grips and decorative panels
  3. Bottom plate removal: Remove screws and carefully lift plate
  4. Top cover removal: Detach mode dial and exposure compensation dial
  5. Rear assembly removal: Disconnect LCD ribbon cables and remove screws
  6. Main board access: Remove shield plates and disconnect all connectors

CAUTION! Document screw locations and sizes. Handle ribbon cables with extreme care.

Maintenance Schedule

Calibration Procedures

Detailed calibration processes for optimal camera performance.

Autofocus Calibration: Use calibration chart at specified distance. Adjust micro-adjustment values for front/back focus issues.

White Balance Calibration: Use gray card under consistent lighting. Create custom white balance profiles.

Exposure Calibration: Verify exposure accuracy using 18% gray card. Adjust exposure compensation if necessary.

Color Calibration: Use color checker chart. Verify color reproduction accuracy across all film simulation modes.

Electrical System

Circuit diagrams and electrical component specifications.

  1. Power Supply Circuit: Battery input, voltage regulation, power distribution
  2. Main Board: Image processor, memory controller, interface circuits
  3. Sensor Board: CMOS sensor, analog front end, timing controller
  4. Display Circuits: LCD driver, viewfinder electronics
  5. Control Circuits: Button matrix, dial encoders, communication buses

Tip: Always verify voltage levels before replacing components. Use approved replacement parts only.

Optical System

Sensor and viewfinder optical path maintenance procedures.

  1. Sensor Cleaning: Use approved sensor cleaning swabs and solution
  2. Viewfinder Optics: Clean eyepiece and internal optics with lens tissue
  3. Mirror Mechanism: Inspect and clean mirror surfaces (if applicable)
  4. Lens Mount Alignment: Verify mount perpendicularity and flange distance
  5. IR Cut Filter: Inspect for scratches or contamination
  6. Anti-aliasing Filter: Check for damage or delamination

WARNING! Never touch sensor surface directly. Use only approved cleaning materials.

Mechanical Components

Shutter mechanism, mirror box, and mechanical assembly maintenance.

Shutter Unit: Curtain timing adjustment, curtain replacement procedures, lubrication points

Mirror Mechanism: Mirror alignment, damper adjustment, return spring tension

Body Assembly: Frame alignment, mounting point inspection, structural integrity

Control Dials: Detent mechanism cleaning, encoder wheel maintenance

Button Assemblies: Contact cleaning, spring replacement, waterproof sealing

Firmware Updates

Camera and lens firmware update procedures and troubleshooting.

Service Tools

Required tools and equipment for proper camera service.

Essential Tools: JIS screwdrivers, spudgers, tweezers, anti-static mat, magnification loupe

Specialized Tools: Sensor cleaning kit, shutter counter reset tool, calibration charts

Test Equipment: Digital multimeter, optical test targets, light source for testing

CAUTION! Use proper tool for each task. Improper tools can damage components.

Troubleshooting Guide

SymptomPossible CauseCorrective Action
Camera won't power onBattery/connectionsCheck battery charge; inspect power switch; verify main board connections
Autofocus not workingLens/sensor issuesTest with different lens; clean contacts; check AF sensor alignment
Image quality issuesSensor/settingsClean sensor; reset camera settings; update firmware
Shutter errorsMechanical failureInspect shutter mechanism; check curtain timing; replace if necessary
Connectivity problemsPorts/softwareCheck cable connections; update drivers; test different ports
Card read errorsCard/slot issuesTry different memory card; clean card contacts; inspect card slot

Factory Reset: Menu > Setup > Reset > Reset All

Service Support: Contact authorized Fujifilm service center for technical assistance

Fuji Prima T2 Service Manual © - All Rights Reserved 2025