Fuji Frenic 5000G11 Manual Download

The Fuji Frenic 5000G11 is a high-performance industrial inverter designed for precise motor control applications. This advanced frequency converter features robust construction, comprehensive protection functions, and flexible programming capabilities suitable for various industrial environments. Below are key sections covering specifications, installation, operation, programming, maintenance, and troubleshooting.

1. Product Overview 2. Technical Specifications 3. Installation Guidelines 4. Wiring Connections 5. Basic Operation 6. Parameter Settings 7. Protection Functions 8. Maintenance Procedures 9. Troubleshooting Guide 10. Download Options

Product Overview

The Fuji Frenic 5000G11 series represents the latest generation of industrial inverters with enhanced performance and reliability features.

Feature	Description
Control Method	V/F Control, Sensorless Vector Control
Frequency Range	0.1 to 400 Hz
Input Voltage	200-240V AC, 380-480V AC (3-phase)
Output Capacity	0.4 to 630 kW
Display Unit	Digital operator with LCD
Communication	RS-485, Modbus RTU
Protection Rating	IP20 (standard)
Ambient Temperature	-10°C to +50°C
Storage Temperature	-20°C to +65°C

Technical Specifications

Model Series: Frenic 5000G11
Input Power: 3-phase 200-240V/380-480V ±10%
Output Power: 3-phase, 0 to rated input voltage
Carrier Frequency: 0.5 to 15 kHz (adjustable)
Control Characteristics: Digital operator/keypad operation
Acceleration/Deceleration: 0.1 to 3600 seconds
Braking: Regenerative braking/DC injection braking
Protection Functions: Overcurrent, overvoltage, undervoltage, overload, overheating
Standards Compliance: CE, UL, cUL

Installation Guidelines

Proper installation is crucial for optimal performance and safety.

Mounting: Install in clean, dry location with adequate ventilation.
Clearance: Maintain minimum 100mm clearance on all sides for cooling.
Environment: Avoid areas with excessive dust, moisture, or corrosive gases.
Grounding: Ensure proper grounding according to local electrical codes.
Vibration: Mount on vibration-resistant surface if required.

WARNING! Installation must be performed by qualified personnel only. Disconnect all power before installation.

Wiring Connections

Follow proper wiring procedures to ensure safe operation.

Power Wiring: Connect R/L1, S/L2, T/L3 to power supply; U/T1, V/T2, W/T3 to motor.
Control Wiring: Use shielded cables for control signals; keep separate from power cables.
Grounding: Connect grounding terminal to proper earth ground.
Braking Resistor: Connect if dynamic braking required.
Communication: Connect RS-485 terminals for network communication.

CAUTION! Ensure all connections are tight and properly insulated.

Basic Operation

Operating the Frenic 5000G11 through the digital operator.

Power On: Apply power; display shows ready status.
Run Command: Use RUN key or external signal to start motor.
Frequency Setting: Adjust output frequency via potentiometer or digital setting.
Monitoring: View operating parameters on LCD display.
Stop: Use STOP key or external signal to stop motor.

Key Functions: RUN, STOP, RESET, UP/DOWN arrows, ENTER, ESC

Parameter Settings

Essential parameters for basic configuration.

Parameter	Function	Setting Range
F01	Frequency Reference 1	0.1 to 400 Hz
F02	Operation Method Selection	0-3
F03	Maximum Output Frequency	50 to 400 Hz
F04	Base Frequency	0.1 to 400 Hz
F05	Rated Voltage	0 to 1000V
F06	Acceleration Time 1	0.1 to 3600 sec
F07	Deceleration Time 1	0.1 to 3600 sec
F08	Electronic Thermal	0.1 to 500.0A

Protection Functions

Comprehensive protection ensures equipment safety.

Overcurrent Protection (OC): Trips at 200% rated current
Overvoltage Protection (OV): Activates when DC bus voltage exceeds limit
Undervoltage Protection (UV): Protects against low input voltage
Overload Protection (OL): Electronic thermal protection for motor
Overheating Protection (OH): Monitors heatsink temperature
Short Circuit Protection: Instantaneous trip for output short circuits
Ground Fault Protection: Detects ground faults in motor circuit

Maintenance Procedures

Regular maintenance ensures long-term reliability.

Visual Inspection: Check for dust accumulation, loose connections, corrosion.
Cleaning: Use dry compressed air to remove dust from heatsinks.
Terminal Check: Verify tightness of power and control terminals.
Cooling System: Ensure fans operate properly; replace if noisy or not spinning.
Capacitors: Check for bulging or leakage in DC bus capacitors.

WARNING! Always disconnect power before performing maintenance.

Troubleshooting Guide

Symptom	Possible Cause	Corrective Action
No display	Power supply issue	Check input power; verify control voltage
Motor not running	Run command missing	Check run signal; verify parameter settings
Overcurrent fault	Motor overload/short	Check motor connections; reduce load
Overvoltage fault	Deceleration too fast	Increase deceleration time; add braking resistor
Overheating fault	Insufficient cooling	Clean heatsink; check fan operation
Communication error	Wiring/parameter issue	Check communication cables; verify settings

Download Options

Access complete documentation for the Fuji Frenic 5000G11 series.

Full User Manual (PDF, 2.5MB)
Installation Guide (PDF, 1.2MB)
Programming Manual (PDF, 3.1MB)
Technical Specifications (PDF, 0.8MB)
Wiring Diagrams (PDF, 1.5MB)

Support: Contact Fuji Electric technical support at +81-3-5435-7200 or visit www.fujielectric.com